GNR-H2200 INDUSTRIAL CONTROLS TRAINING SYSTEM    

The Hampden Model GNR-H2200 Industrial Controls Training System provides students with practical "hands-on" experience in designing, wiring, checking out, and troubleshooting "real-world" motor control systems. The Hampden Industrial Controls Training System consists of a melamine covered wood core panel, on which are mounted interchangeable unitized control modules. The student selects just the components needed for a particular system, secures them on the panel with wing nuts and wires them in accordance with the control diagram. All pushbuttons, contactors and other control components are suitably rated for use with 1HP motors. See attached data sheet for modules available and a typical complement of Hampden Model GNR-H2200 modules.

H-6527 SEDIMENTATION STUDY TRAINER    

The Hampden Model H-6527 Sedimentation Study Trainer has been developed to investigate the physical processes of sedimentation. The student will be able to evaluate and measure the particles as to height, size and settling rates for making up the sedimentation curve.

H-RPT-1 RESIDENTIAL PIPING TRAINER  

The Hampden Model H-RPT-1 Residential Piping Trainer is designed to demonstrate a series of modern waste flushing systems. The H-RPT-1 consists of three modern flushing system: Single Flush Flushometer, Dual Flush Flushometer, and Pressure Assist Water Closet.

H-IRT-1 INDUSTRIAL REFRIGERATION TRAINER    

The Hampden Model H-IRT-1 Industrial Refrigeration Trainer consists of industrial refrigeration components completely factory assembled and wired. It is designed to provide training with larger commercial and industrial refrigeration systems which require water-cooled condensers (tube-in-tube and shell-in-tube), electric and hot gas defrost systems, cooling towers, hot bypass capacity control systems, crankcase pressure regulators, crankcase heaters and pressure pumps.
Options:
H-IRT-1-CDL Industrial Refrigeration Trainer with Computer Data Logging & Software Option (R-134a)
H-IRT-ACC (shown) Air-Cooled Condenser Accessory
H-IRT-EC (shown) Evaporator Chiller
H-IRT-FP-18E (shown) Electrical Fault Package Option
H-IRT-FP-M Mechanical Fault Package Option
H-ACTK-CT Cooling Tower Accessory
H-RST-DMB Digital Manifold with Bluetooth Option

H-6523A SEDIMENT TRANSPORT CHANNEL DEMONSTRATOR   

The Hampden Model H-6523A Sediment Transport Channel Demonstrator investigates suspended sediment in a moving stream and bed load movement. The moving stream can be controlled over a wide range to simulate fast flowing streams or slow moving rivers, demonstrating the various size and density of partial deposits. Slope is adjustable from 0-10%.

IMAGE NOT AVAILABLE

H-MFA-3C FIRE ALARM DEMONSTRATOR    

The Hampden Model H-MFA-3C Fire Alarm Demonstrator is a fully functioning fire alarm system which can be utilized to present the student with a variety of common installation and operational features. The trainer is a composite of basic equipment usually associated with residential and commercial layouts, including: Main Control Panel, Alarm Signal Device, Heat Detector, Smoke Detector, City Circuit Monitor, Pull Station, Remote Annunciator Panel, and Auxiliary Function Panel.

H-6521 MODEL SEDIMENTATION TANK    

The Hampden Model H-6521 Model Sedimentation Tank has been developed to investigate the hydraulic characteristics and setting efficiencies of a model settling basin. The student will be able to evaluate how non-uniform flows occur and its interaction with sediment settling characteristics.

Copyright 2019  CLICK WebDesigns

HAMPDEN ENGINEERING CORPORATION


​sales@hampden.com

P.O. Box 563

​East Longmeadow, MA 01028

​(Toll Free) 800-253-2133 or 888-HEC-CORP

Local: 413-525-3981

​Fax: 413-525-4741​

H-6516 ION EXCHANGE DEMONSTRATOR    

The Hampden Model H-6516 Ion Exchange Demonstrator is a bench mounted unit designed to demonstrate the use of ion exchange resins for either continuous water softening or demineralization. The equipment is designed to emulate the industrial operation of such units, including monitoring breakthrough and regeneration cycles.

H-6515 ANAEROBIC DIGESTER      

The Hampden Model H-6515 Anaerobic Digester is a bench top trainer designed to demonstrate the fundamentals of the anaerobic treatment processes. Anaerobic treatment processes involve bacteria which function only in the absence of air. These processes are becoming more popular in the water treatment industry, as they have considerable advantages over aerobic processes, including low sludge production, tolerance of stop/start operation, production of a useful fuel (methane), and relatively high throughput.

H-6519 PERMEABILITY/FLUIDIZATION STUDIES TRAINER     

The Hampden Model H-6519 Permeability/Fluidization Studies Trainer is designed to investigate the measurement and characteristics of flow through a bed of particles. The trainer consists of metal framework, transparent test section module, constant head module, valve and flowmeter module, water manometer, digital manometer, interconnection tubing and glass beads for the test column.

H-FP-223-14 HYDRAULIC TRAINER   

The Hampden Model H-FP-223-14 Hydraulic Trainer consists of a mobile bench, hydraulic pump, and selection of hardware mounted on a vertical panel. All hydraulics hardware is of commercial quality and configured for training purposes. The vertical panel is constructed of code gauge steel finished in instrument white baked enamel.
Options:
H-FP-223-14-FP Hydraulic Fault System Option
H-FP-223-14-EH Electrohydraulics Option
H-FP-223-14-P Pneumatics Option
H-FP-223-14-A Accumulator Option
H-FP-223-14-JS Joystick Option
H-FP-223-14-PPS Pneumatic Air Supply Option
H-FP-223-14-PLC Programmable Logic Controller
H-FP-223-14/15-CD Simulator Software Option for Hydraulics and Pneumatics

H-6524 MOBILE BED AND FLOW VISUALIZATION TANK DEMONSTRATOR    

The Hampden Model H-6524 Mobile Bed and Flow Visualization Tank Demonstrator is used to investigate flow visualization and mobile bed situations in relation to Civil Engineering structures.

H-ICS-8189-4 INSTRUMENTATION AND CONTROLS TRAINER  

The Hampden Model H-ICS-8189-4 Instrumentation and Controls Trainer provides experience in setting up, tuning, operating, and troubleshooting actual instrument and control systems of the type used in the power and process industries. By simulating a different process loop, this unit provides instruction in the measuring and transducing of such physical variables as pressure, temperature, flow and level. Students and trainees learn instrumentation and control techniques of standard commercial manufacturers, such as Yokogawa, and Rosemount. Various types of closed-loop control: on/off, proportional, proportional plus integral, and proportional plus integral plus derivative, as well as a variety of final control devices, including electric, pneumatic and electronic are covered.
Options:
H-ICS-X Interface Package and Program for IBM Compatible

H-6852 MODULAR HEAT EXCHANGER SYSTEM  

The Hampden Model H-6852 Modular Heat Exchanger System has been developed to investigate the fundamental principles of heat transfer devices. The apparatus permits the student to move from classroom theory to hands-on applications with practical training. The student shall measure the variables that affect the overall heat transfer coefficient. The hot and cold fluid temperatures as well as flow rates are monitored at strategic locations. The unit can be configured to operate four different types of heat exchanger modules using quick connect couplers eliminating the use of tools. 
The Model H-6852 Modular Heat Exchanger System consists of the following modules: 
H-6852-A Control Module 
H-6852-B Service Module 
H-6852-G Thermocouple Module Set (4) 
H-6852-H Thermocouple Probe 
H-6852-I Flow Transducer Module set (2) 
H-6852-K Hose Set (various lengths) 
(Model H-6852 Modular Heat Exchanger System shown with optional modules;

H-6852-D, -E, -F, and -J)
Options:
H-6852-C Concentric Tube Heat Exchanger Module Option
H-6852-D Shell-and-Tube Heat Exchanger Module Option
H-6852-E Plate Heat Exchanger Module Option
H-6852-F Jacketed Tank with Stirrer Option
H-6852-J Data Logging I/0 Module (LabVIEW w/o Software)

H-6252 MODULAR CHEMICAL REACTOR SYSTEM  

The Hampden Model H-6252 Modular Chemical Reactor System is used to investigate the chemical reactor which is the most commonly used, important piece of equipment in a chemical plant. Chemical reactors are used to manufacture a wide variety of products including: polyvinyl chloride, epoxy resin, and pharmaceuticals, to name a few. The Hampden Model H-6252 Modular Chemical Reactor System consists of the following Modules: H-6252-A Reagent Service Module (2) H-6252-B Hot Water Service Module (1) H-6252-C Batch Reactor Module (1) H-6252-D Tubular Reactor Module (1) H-6252-E Continuous Stirred Tank Reactor Module (1) H-6252-F Control Module (1) H-6252-H Hose Set (1) H-6252-J Product Tank Module (1)
Options:
H-6252-I Flow Transmitter Module Option (2)
H-6252-G Data Logging I/O Module Option (LabVIEW w/ Software) (1)

workforce development

H-6535 HYDROSTATICS BENCH  

The Hampden Model H-6535 Hydrostatics Bench consists of an assortment of apparatus needed for experiments into the properties of fluids and hydrostatics, including all of the plumbing, pumps and valve control to direct the fluids in the system. Also included is a built-in safety feature that directs fluid into flasks in the case of over-pressurizing the manometers.

H-181A STEAM POWER PLANT SYSTEM (BOILER TRAINER)   

The primary function of the Hampden Model H-181A Steam Power Plant System (Boiler Trainer) is to demonstrate to the student how a boiler makes steam for power generation. This model features full-function automatic controls at all points in the process.
Options:
HGS-TI Test Instrument Package
HGS-OST Oil Supply Tank
H-181-A-NO Nozzle Experiment
H-181-A-HO Heat Exchanger Experiment
H-181-A-LO Loads Experiment

H-6517 AERATION UNIT     

The Hampden Model H-6517 Aeration Unit has been developed to investigate oxygen transfer characteristics of diffused air systems along with physical and chemical parameters which effect oxygenation in terms of retention time. The level of Dissolved Oxygen (DO) in water depends on many physical, chemical and biochemical activities in the sample. The most important factors to consider are pressure, temperature and salinity. The amount of oxygen a sample can hold in a solution will vary with the temperature of the sample, the pressure or altitude at which the sample is measured and the concentration of salts dissolved in the sample. The analysis of DO is one of the key tests performed in water pollution and waste water treatment studies.

H-6809 SOLID HANDLING INVESTIGATION BENCH    

The Hampden Model H-6809 Solid Handling Investigation Bench has been designed to allow students to familiarize themselves with various methods of handling solids through blending, separating, sizing, discharge rates, angle of repose, grinding, and material transport.

H-185-2A ADVANCED BOILER TRAINER   

The Hampden Model H-185-2A Advanced Boiler Trainer serves to demonstrate principles of operation and troubleshooting techniques of a current model boiler system. The modules front panel displays a complete pictorial view of the system. All functions operate as on the actual equipment and present the student with realistic problem solving opportunities. Hampden H-LTCS Laptop Computer System is included.

44 FOOT GOOSENECK TRAILER    

The Hampden 44 foot Gooseneck Trailer comes complete with air conditioning and electrical power included in the system. Other options are generator system to run air conditioning and electrical power, recharge capability through direct plug of power source. The trailer is used as a mobile training facility and is designed to haul equipment to differnet training sights
Options:
Video System Package
Storage Units
Workbenches

H-6520 INFILTRATION DEMONSTRATOR    

The Hampden Model H-6520 Infiltration Demonstrator investigates the infiltration rates of different soil types and soil surface treatments. This unit consists of a table top base and panel assembly, sump tank tray, three glass cylinders, upper and lower bracket assembly and a graduated beaker. (shown with accessories)

www.hampden.com/logo

H-6150 LIQUID-TO-LIQUID EXTRACTION DEMONSTRATOR  

The Hampden Model H-6150 Liquid-To-Liquid Extraction Demonstrator has been developed to permit student study of the fundamentals of a liquid-to-liquid extraction system. In addition to demonstrating the hydrodynamics of liquid-to-liquid extraction systems and interface control techniques, this unit can also be used to determine the mass transfer rates, heat transfer coefficients, extraction efficiency, and operating conditions at different liquid flow rates. The extraction process can be operated in a continuous or semi-continuous mode.
Options:
H-6150-CDL Liquid-To-Liquid Extraction Demonstrator with Computer Data Logging Option (LabVIEW w/ Software)

PST-1 PLUMBING TRAINER  

The Hampden Model PST-1 Plumbing Trainer is used to demonstrate an environmentally friendly toilet flushing system. Utilizing gray water, i.e., water drained from a sink, the vanity tank will fill and pump the gray water into the water storage tank of a standard toilet. The gray water will be used to flush the toilet instead of using clean water.

H-RIG-1C RIGGING SYSTEMS TRAINER  

The Hampden Model H-RIG-1C Rigging Systems Trainer is designed to teach the techniques of safely moving loads of various shapes, sizes and types. The Hampden Rigging System contains a variety of lifting and moving devices to allow the student to learn the proper methods of moving loads safely.

H-6529 FLOCCULATION TEST UNIT     

The Hampden Model H-6529 Flocculation Test Unit is used to determine optimal chemical dosages for flocculation. The Flocculation Test Unit helps you to determine the exact amount of alum or polymer necessary to trigger flocculation.

H-PPST-1 PIPING/ PIPEFITTERS SYSTEM TRAINER  

The Hampden Model H-PPST-1 Piping/ Pipefitters System Trainer provides the student with a "hands-on" trainer for piping. The student will learn the necessary methods of connecting and running metal/iron piping, plastic piping, copper tubing, and hydraulic hose. Each material has its own particular methods used in plumbing.

H-RCSD-3A RESIDENTIAL/ COMMERCIAL REMOTE CONTROL SWITCHING DEMONSTRATOR    

The Hampden Model H-RCSD-3A Residential/ Commercial Remote Control Switching Demonstrator provides a complete trainer showing a state-of-the-art building wiring system control of lighting and appliances via programmed or manual remote. The Model H-RCSD-3A is based on the LonWorks® Control System using the various building automation components designed to simulate a residential/commercial wiring system, including a complete comprehensive training program. These devices freely exchange operating system information utilizing an internally accepted and LonMark® Interoperability Association controlled open protocol.

H-RST-2 REFRIGERANT SYSTEM TRAINER    

The Hampden Model H-RST-2 Refrigerant System Trainer was designed to provide students with an actual working model of a refrigeration system, complete in every detail. Its clear glass design allows the student to watch the refergerant change state.
Options:
H-RST-2-CDL Refrigerant System Trainer with Computer Data Logging & Software Option (R-123)
H-RST-MP Instrument Package Option
H-RST-FP-10E Electrical Fault Package Option
H-RST-TP Test Points Option (adder for H-RST-FP-10E Option)
H-RST-DMB Digital Manifold with Bluetooth Option

H-IMTS-1 INDUSTRIAL MAINTENANCE TRAINING SYSTEM    

The Hampden Model H-IMTS-1 Industrial Maintenance Training System provides maintenance technicians with the equipment needed to learn state-of-the-art techniques for maintaining complex drive systems through "hands-on" practice.
Options:
H-IMTS-GB Gearbox Maintenance Trainer
H-IMTS-BM Bearing Module Trainer
H-IMTS-BC Industrial Maintenance Training System-Bed Conveyers
H-IMTS-DT DVD Training Package
H-IMTS-CP Courseware Package
H-IMTS-CDL Computer Data Logging Package
H-IMTS-EBM Electric Brake & Clutch Module
H-IMTS-STP Special Tools Package
H-IMTS-TEP Test Equipment Package
H-IMTS-LAK Laser Alignment Kit
H-IMTS-VAK Vibration Analysis Kit
H-IMTS-2S Second Student Package

H-ICS-8189-4PH INSTRUMENTATION, CONTROLS & PH CONTROL TRAINER  

The Hampden Model H-ICS-8189-4pH Instrumentation, Controls & pH Control Trainer provides experience in setting up, tuning, operating, and troubleshooting actual instrument and control systems of the type used in the power and process industries. By simulating a different process loop, this unit provides instruction in the measuring and transducing of such physical variables as pressure, flow, level and pH. Students and trainees learn instrumentation and control techniques of standard commercial manufacturers, such as Yokogawa, and Rosemount. Various types of closed-loop control: on/off, proportional, proportional plus integral, and proportional plus integral plus derivative, as well as a variety of final control devices, including electric, pneumatic and electronic are covered.
Options:
H-ICS-X Interface Package and Program for PC Computer

H-DTT-26-120 TRANSFORMER LAB KIT - 120V INPUT  

The Hampden Model H-DTT-26-120 Transformer Lab Kit - 120V Input allows students to correctly make connections to power transformers located on utility poles. Following instruction, students will work in a lab using miniature hardware that mimics the appearance of real-world equipment. They will use an apparatus that looks like a short length of power line. The upper 3 wires will represent the high voltage line (an optional 4th wire, representing a common neutral is also supplied), the lower 3 wires (4 wires for some configurations) will represent the service voltages from the transformer to the customers secondary connections.
Options:
H-DTT-26-FP Electrical Fault Package
H-DTT-26-CSX Color-coded Cord Set
H-DTT-26-X-3T-B2 Blue Transformer Set 120V/12-24V (3 per set)
H-DTT-26-X-3T-Y2 Yellow Transformer Set 120V/12V (3 per set)
H-DTT-26-X-3T-R2 Red Transformer Set 120V/24-48V (3 per set)
H-DTT-26-X-3T-G2 Green Transformer Set 208V/27V (3 per set)
H-PRM-26 Phase Rotation Meter
H-HMR-26 Roll Around Storage Cabinet for all components of 6 lab sets

H-ETS-1A ETHANOL TRAINING SYSTEM 

The Hampden Model H-ETS-1A Ethanol Training System is designed to facilitate the instruction of students on the process required to produce ethanol for experimental purposes. Ethanol is a very promising fuel alternative to oil since sources are widely available and ethanol is clean-burning. The student will be able to observe and control the process of producing ethanol from corn, sugar, sorghum, fruits or several other sources. When using this unit along with the Fractional Distillation option, it is possible to produce ethanol with up to 96% purity. (H-ETS-1A-CDL is shown)

H-PLC-PP-1A-ML-1200 PROGRAMMABLE LOGIC CONTROL TRAINING SYSTEM   

The Hampden Model H-PLC-PP-1A-ML-1200 Programmable Logic Control Training System offers a complete package that provides students with an industry standard PLC and hardware that allows them to design, connect and debug real-world circuits. The Programmable Logic Control Training System provides students with hands-on experience, utilizing standard commercially available programmable logic controllers interfaced with actual input and output devices. The Hampden Model H-PLC-PP-1A-ML-1200 Programmable Logic Control Training System is a complete system that utilizes an Allen-Bradley Micrologix 1200 PLC linked with a Hampden Model H-PLC-PP Peripheral Panel. The Allen-Bradley Micrologix PLC is a state-of-the-art, high capacity, self-contained system with 1000 Instruction capacity, a power supply, 24 AC inputs and 16 AC outputs, mounting rack and Hampden Model H-LTCS Laptop Computer System in one complete package.
Options:
H-RS-LOGIX Programming and Documentation Software
H-RS-LOGIX-LT RS Logix Starter Software
H-PLC-VTS Video (VHS) Training Series
H-PLC-VTS-ECS Electronic Courseware Series Software
1747-PIC Personal Computer Interface Converter
H-PLC-CS Desktop Computer
H-PLC-PO Printer

H-FP-223-15 PNEUMATIC TRAINER    

The Hampden Model H-FP-223-15 Pneumatic Trainer consists of a mobile bench, storage drawer, and a selection of commercial quality hardware, mounted on a 11 gauge white steel vertical panel, mounted on a frame of 14 gauge steel. Finished in instrument tan texture enamel. The mobile bench is constructed of code gauge steel finished in instrument tan texture enamel with four swivel casters, two with locks. The bench includes a locked storage drawer. The bench top is of a pan construction with replaceable non woven absorbent mat. A storage shelf and provisions are provided for mounting the optional compressor.
Options:
H-FP-223-15-FP Pneumatic Fault System Option
H-FP-223-15-PPS Pneumatic Air Supply Option
H-FP-223-15-EPS Electro-Pneumatics Module Option
H-FP-223-15-PLC Programmable Logic Controller
H-FP-223-14/15 CD Simulator Software for Hydraulics and Pneumatic Option

H-6518 AEROBIC DIGESTER      

The Hampden Model H-6518 Aerobic Digester is a bench top trainer designed as a comprehensive study facility of biological water treatment processes. A synthetically prepared waste water is used to gain a working knowledge of the operational parameters and purification efficiencies.

HMD-100-CM DELUXE MOBILE EXPERIMENTATION STATION    

The Hampden Model HMD-100-CM Deluxe Mobile Experimentation Station contains AC/DC power supples, AC instrumentation, DC instrumentation, single-phase and three-phase wattmeter panel, work surface area, and locked storage compartment. Alternate #1: Hampden Model HMD-100-CM-DA Deluxe Mobile Experimentation Station with Digital Meters. Alternate #2: Hampden Model HMD-100-CM-DA-CDL Deluxe Mobile Experimentation Station with Digital Meters and with Motor Generator Interface; and Hampden Model HMD-CS Desktop Computer Systerm Option.

H-DTT-26 TRANSFORMER LAB KIT - THREE PHASE INPUT  

The Hampden Model H-DTT-26 Transformer Lab Kit - 3 Phase Input allows students to correctly make connections to power transformers located on utility poles. Following instruction, students will work in a lab using miniature hardware that mimics the appearance of real-world equipment. They will use an apparatus that looks like a short length of power line. The upper 3 wires will represent the high voltage line (an optional 4th wire, representing a common neutral is also supplied), the lower 3 wires (4 wires for some configurations) will represent the service voltages from the transformer to the customers secondary connections.)
Options:
H-DTT-26-FP Electrical Fault Package
H-DTT-26-CSX Color-coded Cord Set

H-DTT-26-X-3T-B2 Blue Transformer Set 120V/12-24V (3 per set)
H-DTT-26-X-3T-Y2 Yellow Transformer Set 120V/12V (3 per set)
H-DTT-26-X-3T-R2 Red Transformer Set 120V/24-48V (3 per set)
H-DTT-26-X-3T-G2 Green Transformer Set 208V/27V (3 per set)
H-PRM-26 Phase Rotation Meter
H-HMR-26 Roll Around Storage Cabinet for all components of 6 lab sets

H-6528 FILTERABILITY INDEX UNIT    

The Hampden Model H-6528 Filterability Index Unit has been developed to investigate filters and how they relate to water treatment. The student will be able to evaluate the operation and principles of filter operation, filtration procedures and the measurement of filterability of suspended sedimentation.

BIO-100 BIO DIESEL DEMONSTRATOR 

The Hampden Model H-BIO-100 Bio Diesel Demonstrator is ideal for the small producer using the same protocol and with the same quality construction as the larger units. Bio Diesel units are chosen for their rugged design, ease of use, no wash process protocol and price/capacity ratio.