H-6310 MATERIALS STRENGTHS TESTER 

The Hampden Model H-6310 is a hydraulic tensile testing machine with a screw-type operating cylinder which gives completely smooth and step-less loading. The cylinder is operated by means of a crank which is designed so that only light hand power is required to obtain maximum load. The pedagogic design of the machine means that the student can observe what is happening throughout the entire procedure.
Options:
H-6310-10 Tensile Test Rod Set Option
H-6310-20 Brinell Test Piece Set Option
H-6310-31 Bending Device Option
H-6310-32 Large Compression Plates Option
H-6310-33 Helical Spring Test Option
H-6310-34 Disc Spring Test Option
H-6310-36 Shear Test Option
H-6310-37 Deep Draw Test Option
H-6310-38 PC-Aided Measurement Recording System Option

H-6920 PIPE FRICTION DEMONSTRATOR 

The Hampden Model H-6920 Pipe Friction Demonstrator provides complete facilities for the investigation of the phenomena associated with incompressible fluid flow in conduits. (H-6920 shown with accessories)
Options:
H-6920-CDL Pipe Friction Demonstrator with Computer Data Logging Option (LabVIEW w/o Software)
H-6920-11 Venturi Tube Option
H-6920-12 Pitot Tube Option
H-6920-13 Flow Nozzle Option
H-6920-14 Vortex Flowmeter Option
H-6920-14-CDL Vortex Flowmeter with Computer Data Logging Option
H-6920-15 Turbine Flowmeter Option
H-6920-15-CDL Turbine Flowmeter with Computer Data Logging Option
H-6920-16 Magnetic Flowmeter Option
H-6920-16-CDL Magnetic Flowmeter with Computer Data Logging Option
H-6920-17 Mass Flowmeter Option
H-6920-20 Differential Pressure Transmitter (Pipe Friction) Option
H-6927-10 Digital Manometer Option
H-6920-22 Water Pump System Option
H-6920-31 Globe Valve Option
H-6920-32 Butterfly Valve Option
H-6920-33 Ball Valve Option
H-6920-34 Needle Valve Option
H-6920-35 Gate Valve Option
H-6920-37 Stainless Steel Pipe and Plastic Pipe Interchangeable Sections Option
H-6920-MR Mobile Storage Cart Option,

H-6984 ROTODYNAMIC PUMP TEST TRAINER       

 The Hampden Model H-6984 Rotodynamic Pump Test Trainer provides a hands-on introduction to the centrifugal and axial flow pumps.

H-6810 PRESSURE MEASUREMENT BENCH   

The Hampden Model H-6810 Pressure Measurement Bench consists of various components designed to demonstrate practical measurements. It can be used to test and calibrate other pressure instruments and consists of the following: 

  • Test Bench 
  • Pressure Transducers 
  • Test Gauge 
  • Dead Weight Tester 
  • Vacuum-Pressure Air Pump 
  • Manometers

Options:
H-6810-10 PV Transducer Option
H-6810-11 Oscilloscope (60 MHz) Option

H-6715 REFRIGERATION CYCLE DEMONSTRATOR 

The Hampden Model H-6715 Refrigeration Cycle Demonstrator provides the student with an introduction to the Second Law of Thermodynamics, which states that heat will not pass from a cold region to a hot region without an external agency. The student will be able to observe the evaporator where heat is taken in as the liquid evaporates at low pressure and the condenser where the high pressure vapor condenses and rejects heat. The compressor uses a work input to increase the pressure vapor and the expansion valve controls the flow of liquid from the condenser back to the evaporator.
Options:
H-6715-CDL Refrigeration Cycle Demonstrator with Computer Data Logging Option
H-6715-10 Instrument Package Option

H-6852 MODULAR HEAT EXCHANGER BASE SET    

The Hampden Model H-6852 Modular Heat Exchanger System has been developed to investigate the fundamental principles of heat transfer devices. The apparatus permits the student to move from classroom theory to hands-on applications with practical training. The student shall measure the variables that affect the overall heat transfer coefficient. The hot and cold fluid temperatures as well as flow rates are monitored at strategic locations. The unit can be configured to operate four different types of heat exchanger modules using quick connect couplers eliminating the use of tools. 
The Model H-6852 Modular Heat Exchanger System consists of the following modules: 
H-6852-A Control Module 
H-6852-B Service Module 
H-6852-G Thermocouple Module Set (4) 
H-6852-H Thermocouple Probe 
H-6852-I Flow Transducer Module set (2) 
H-6852-K Hose Set (various lengths) 
(Model H-6852 Modular Heat Exchanger System shown with optional modules; H-6852-D, -E, -F, and -J)
Options:
H-6852-C Concentric Tube Heat Exchanger Module Option
H-6852-D Shell-and-Tube Heat Exchanger Module Option
H-6852-E Plate Heat Exchanger Module Option
H-6852-F Jacketed Tank with Stirrer Option
H-6852-J Data Logging I/0 Module (LabVIEW w/o Software)

engineering systems

mechanical engineering program

H-6899A THERMAL RADIATION DEMONSTRATOR    

The Hampden Model H-6899A Thermal Radiation Demonstrator is designed to enable the student to investigate fully the fundamental aspects of radiation heat transfer. Radiant energy emitted from various sources is absorbed by media with different characteristics.
Options:
H-6899A-10 Long Pass Filter Option
H-6899A-20 Narrow Band Pass Filter Option
H-6899A-CDL Thermal Radiation Demonstrator with Computer Data Logging Option (LabVIEW w/o Software)

H-6850-20 DOUBLE-PIPE HEAT EXCHANGER DIGITAL (W TO S)  

The Hampden Model H-6850-20 Double-pipe Heat Exchanger is used to investigate the fundamental principles of heat transfer as applied to a tube-in-tube heat exchanger. The apparatus permits the student to move from classroom theory to a hands-on application with all of the practical training. The student shall measure the variables that affect the overall heat transfer coefficient. The "cold" and "hot" fluid temperatures and flow rates are monitored at strategic locations. The unit can be configured to operate as either a parallel flow or counterflow heat exchanger. By varying the fluid flow rates, laminar, transitional or turbulent flow conditions can be created.
Options:
H-6850-20A Hot Water System Option
H-6850-20B Weight Tank Option
H-6850-20C Platform Scale Option
H-6850-20D Mobile Equipment Carrier Option

H-6640 AIR FLOW UNIT 

The Hampden Model H-6640 Air Flow Unit is designed to provide the basic air flow facilities necessary to perform fundamental experiments in fluid mechanics and heat transfer. With this unit, the student is able to investigate the characteristics of fans and, with the optional heat transfer modules, investigate the characteristics of liquid to liquid and air to liquid heat transfer.
Options:
H-6640-10 Liquid to Air Heat Transfer Modules Option
H-6640-20 Expansion Coil Heat Exchanger Option
H-6640-40 Air Temperature Measurement Package Option
H-6640-50 Axial (Propeller) Fan and Reducer Section Option

H-6523A SEDIMENT TRANSPORT CHANNEL DEMONSTRATOR          

The Hampden Model H-6523A Sediment Transport Channel Demonstrator investigates suspended sediment in a moving stream and bed load movement. The moving stream can be controlled over a wide range to simulate fast flowing streams or slow moving rivers, demonstrating the various size and density of partial deposits. Slope is adjustable from 0-10%.

H-6856 CROSS-FLOW HEAT EXCHANGER    

The Hampden Model H-6856 Cross-Flow Heat Exchanger has been developed to permit students to investigate the heat transfer phenomena occurring in flow over tubes arranged individually or in banks. Air is used as the working fluid and is forced to flow over electrically heated tubes housed in an air duct. The student will be able to monitor heater wattage, heater temperature, and air temperature; while measuring the air velocity in the duct.
Options:
H-6856-10 Finned Tube Plate Option
H-6856-20 Heat Transfer Plate Option
H-6856-CDL Cross-Flow Heat Exchanger with Computer Data Logging Option (LabVIEW w/o Software)

H-6820 DUAL HEAT PUMP DEMONSTRATOR   

The Hampden Model H-6820 Dual Heat Pump Demonstrator demonstrates the fundamental aspects of a heat pump system. This system, which utilizes both air and water as a heat source, allows the student to measure the temperature and pressure at critical points throughout the cycle to better understand the various processes that occur in the heat pump system.
Options:
H-6820-CDL Dual Heat Pump Demonstrator with Computer Data Logging Option (LabVIEW w/o Software)

H-6710 REFRIGERATION DEMONSTRATOR 

The Hampden Model H-6710 Refrigeration Demonstrator has been designed to illustrate the fundamental aspects of the refrigeration cycle. This unit allows the student to measure the temperature and pressure at critical points throughout the cycle to better comprehend the processes that occur in the refrigeration cycle.
Options:
H-6710-CDL (as shown) Refrigeration Demonstrator with Computer Data Logging Option (LabVIEW w/o Software)

H-6646 GEAR PUMP TRAINER 

The Hampden Model H-6646 Gear Pump Trainer provides a hands-on introduction to the gear pump and its operation. The trainer uses sensors which interface with the Hampden MODEL H-6648 Control Interface Module sold separately.

IMAGE NOT AVAILABLE

H-6985 WATERHAMMER TRAINER        

The Hampden Model H-6985 Waterhammer Trainer provides a hands-on introduction to the destructive forces existing in pumping installations where the rate of flow changes abruptly for various reasons. Theory and mechanics of computing waterhammer in pump discharge lines have advanced rapidly, the practical aspects of this subject are still confusing to engineering students.
Options:
H-6985-CDL Waterhammer Trainer with Computer Data Logging Option (LabVIEW w/o Software)
H-6985-10 Water Surge Option

H-6960 LAMINAR FLOW ANALYSIS DEMONSTRATOR      

The Hampden Model H-6960 Laminar Flow Analysis Demonstrator allows students to do experiments of two-dimensional problems associated with laminar flow. A dye injection system allows the flow patterns to be seen more vividly and easier to videotape or photograph. Lexan shapes are provided to assist the student in assembling flow pattern experiments.

Copyright 2021  CLICK WebDesigns

H-6740 AIR VENTILATION SYSTEM TRAINER  

The Hampden Model H-6740 Air Ventilation System Trainer permits the operational study of residential, commercial, and industrial air ventilation systems.
Options:
MODEL H-6740-CDL Computer Data Logging Option
MODEL H-6740-10 High Velocity Experiments Package Option

H-6950 FLOW MEASUREMENT UNIT      

The Hampden Model H-6950 Flow Measurement Unit is designed to demonstrate the fundamental principles of flow measurement. Standard industrial flow sensors are used to measure the flow rates. The student can measure the primary output of the flow sensor; e.g. differential pressure, frequency or pulse; and measure the secondary (flow rate) signal. In addition, the student can also measure the pressure drop of each flow sensor and water temperature. Thus the student is able to check the accuracy, linearity and repeatability of each flow sensor and necessary transducers.
Options:
H-6950-CDL Flow Measurement Unit with Computer Data Logging Option (LabVIEW w/o Software)
H-6950-20 Turbine Flowmeter Option
H-6950-20-CDL Turbine Flowmeter w/ CDL Option
H-6950-30 Vortex Flowmeter Option
H-6950-30-CDL Vortex Flowmeter w/ CDL Option
H-6950-40 Magnetic Flowmeter Option
H-6950-40-CDL Magnetic Flowmeter w/ CDL Option

IMAGE NOT AVAILABLE

IMAGE NOT AVAILABLE

H-6898 THERMO RADIATION TRAINER    

The Hampden Model H-6898 Thermo Radiation Trainer enables the student to investigate fully the fundamental aspects of radiation heat transfer. Radiant energy emitted from various sources is absorbed by media with different characteristics.
Options:
H-6898-CDL Thermo Radiation Trainer with Computer Data Logging Option (LabVIEW w/o Software)

H-6805 TEMPERATURE MEASUREMENT BENCH, TYPE K  

The Hampden Model H-6805 Temperature Measurement Bench is designed to allow students to determine the operating characteristics of temperature measuring devices. The student is able to measure the accuracy, response time, repeatability, hysteresis and other characteristics of a temperature measuring device. The unit can also be used to test temperature measuring devices against reference standards. Model H-6805 shown with optional Model H-6805-10 and Model H-6805-20.
Options:
H-6805-10 Air Compressor and Pressure Regulator Option
H-6805-20 Thermistor Package Option
H-6805-30 Thermocouple Type J Package Option
H-6805-40 Thermocouple Type T Package Option
H-6805-50 Thermocouple Type E Package Option

H-CLT-1 COMBUSTION LABORATORY TRAINER         

The Hampden Model H-CLT-1 Combustion Laboratory Trainer gives accurate control of fuel to air ratios of various weak to rich fuel mixtures.
Options:
H-CLT-CA Combustion Analyzer Accessory
H-CLT-1-CDL Combustion Laboratory Trainer with Computer Data Logging and Software Option

H-6850 HEAT TRANSFER UNIT 

The Hampden Model H-6850 Heat Transfer Unit has been designed to provide the primary facilities for generating heated and chilled water.

HAMPDEN ENGINEERING CORPORATION


​sales@hampden.com

P.O. Box 563

​East Longmeadow, MA 01028

​(Toll Free) 800-253-2133 or 888-HEC-CORP

Local: 413-525-3981

​Fax: 413-525-4741​

H-6982 MULTI-PUMP TEST BENCH (WITH PISTON PUMP)      

The Hampden MODEL H-6982 Multi-Pump Test Bench provides a hands-on introduction to pump design and application. The student will operate each of the test pumps in various modes using the provided instrumentation for flow, speed, head and torque measurements.

H-6825 VAPOR JET REFRIGERATION/HEAT PUMP 

The Hampden Model H-6825 Vapor Jet Refrigerator/Heat Pump demonstrates the principle that transferring heat from a cold to a hot source is impossible without external assistance, i.e. high grade heat input.
Options:
H-6825-WC Water Chiller Option

H-6644 CENTRIFUGAL PUMP TRAINER 

The Hampden Model H-6644 Centrifugal Pump Trainer provides a hands-on introduction to the centrifugal pump and its operation. The trainer uses sensors which interface with the Hampden MODEL H-6648 Control Interface Module sold separately.

H-FPST-1 FLAME PROPAGATION AND STUDY TRAINER         

The Hampden Model H-FPST-1 Flame Propagation and Study Trainer is used to investigate the physical behavior of flame and flame control whenever fuels are burned.

H-6826 VORTEX TUBE REFRIGERATOR 

The Hampden Model H-6826 Vortex Tube Refrigerator permits the study of the characteristics of vortex tube refrigerating effects. The student has the opportunity to determine the ability to produce cold air from a device with no moving parts.

H-6970 HYDROKINETICS DEMONSTRATOR       

The Hampden Model H-6970 Hydrokinetics Demonstrator is designed to demonstrate characteristics of turbulent and laminar flow, significance of Reynold's Numbers, flow around objects, velocity distribution in duct flow, formation of shock waves by an air foil, two dimensional flows, the Karman Street Vortex, diffuser performance and the conditions at enlargement and contraction passage.
Options:
H-6970-U Digital Ultrasonic Height Gauge Option
H-6970-CDL Hydrokinetics Demonstrator with Computer Visual Data Logging Option

H-6980 SERIES PARALLEL PUMP TEST DEMONSTRATOR     

The Hampden Model H-6980 Series/Parallel Pump Test Demonstrator provides hands-on experience with the centrifugal pump in both series and parallel configurations. The Model H-6980 is a bench-mounted pumping system permitting students to explore pumping mechanics and its effects. The unit provides two methods of determining flow rate which can be manually adjusted using a throttle valve. One method utilizes an orifice plate and manometer. The other utilizes a vernier hook gauge, a V-notch weir, and equations.
Options:
H-6980-CDL Series Parallel Pump Test Demonstrator with Computer Data Logging Option (LabVIEW w/o Software)
H-6980-11 Regenerative Turbine Pump Option
H-6980-12 Gear Pump Option
H-6980-13 Flexable Impeller Pump Option

H-6872 FILM & DROP DEMONSTRATOR  

The Hampden Model H-6872 Film & Drop Condensation Demonstrator has been developed to investigate the mechanisms involved in heat transfer with systems that undergo a phase change. The student is able to observe condensation phenomena and correlate the results with film condensation theory. The trainer is designed to provide both film and drop condensation.
Options:
H-6872-CDL (as shown) Film & Drop Demonstrator with Computer Data Logging Option (LabVIEW w/o Software)

H-6350 NOZZLE PRESSURE DISTRIBUTION TRAINER          

The Hampden Model H-6350 Nozzle Pressure Distribution Trainer allows the student to investigate pressure distribution and mass flow rate in nozzles. Three types of nozzles are provided covering convergent and convergent-divergent.
Options:
H-6350-CDL (as shown) Nozzle Pressure Distribution Trainer with Computer Data Option (LabVIEW w/o Software)

H-6878-10 MOBILE ELECTRIC STEAM BOILER   

The Hampden Model H-6878-10 Mobile Electric Steam Boiler has been designed to provide steam for use with the Hampden Model H-6878 Six-Pass Heat Exchanger, or other units where steam may be a requirement.

H-6671 TWO STAGE AIR COMPRESSOR TRAINER         

The Hampden Model H-6671 Two-Stage Air Compressor Trainer has been designed to demonstrate thermodynamic principles of a 2-stage air compressor.

H-6986 UNIVERSAL PUMP TEST TRAINER         

The Hampden Model H-6986 Universal Pump Test Trainer provides a hands-on introduction to centrifugal, axial, gear and piston pumps. 

H-6910-12A WIND TUNNEL    

The Hampden Model H-6910-12A Wind Tunnel has been designed to provide the fundamental air flow facilities necessary to perform any of the H-6910-12A Series Wind Tunnel Experiments. This unit is mobile so that it is suitable for either a lecture hall demonstration or laboratory work.
Options:
H-6910-12-5X Manometer Package Option
H-6910-12-6 Manometer Package Option
H-6910-12-10 Bernoullis Equation Apparatus Option
H-6910-12-25 Free Jet/Flow In Bends Demonstrator Option
H-6910-12-40 Boundary Layer Demonstrator Option
H-6910-12-55 Lift and Drag Force Demonstrator Option
H-6910-12-70 Pressure Wing & Rake Option
H-6910-12-71 Wing with Slat and Flap and Load Cell Interface Option
H-6910-12-72 Pressure Cylinder Option
H-6910-12-73 Flutter Wing Option
H-6910-12-80 Probe Accessory Package Option
H-6910-12A-CDL (as shown) Computer Data Logging Option (LabVIEW w/o software)

IMAGE NOT AVAILABLE

H-6858 LAMINAR/VISCOUS FLOW HEAT TRANSFER DEMONSTRATOR    

​The Hampden Model H-6858 Laminar/Viscous Flow Heat Transfer Demonstrator has been developed to investigate the fundamental principles of heat transfer as applied to a tube-in-tube heat exchanger. The apparatus permits the student to move from classroom theory to a hands on application with all of the nuances that it entails. The student shall measure the variables that affect the overall heat transfer coefficient. The cold and hot fluid flow rates are measured. The unit can be configured to operate as either a parallel flow or counterflow heat exchanger. By varying the fluid flow rates, laminar, transitional or turbulent flow conditions can be created.
Options:
H-6858-CDL Laminar/Viscous Flow Heat Transfer Demonstrator with Computer Data Logging Option

H-6857 WATER FLOW HEAT TRANSFER DEMONSTRATOR    

The Hampden Model H-6857 Water Flow Heat Transfer Demonstrator has been developed to investigate the fundamental principles of heat transfer as applied to a tube-in-tube heat exchanger.

H-6910 WIND TUNNEL W/VARIABLE FREQUENCY DRIVE    

The Hampden Model H-6910 Wind Tunnel has been designed to provide the fundamental air flow facilities necessary to perform any of the H-6910 Series Wind Tunnel Experiments.
Options:
H-6910-5 Manometer Package Option
H-6910-10 Bernoullis Equation Demonstrator Option
H-6910-25 Free Jet/Flow In Bends Demonstrator Option
H-6910-40 Boundary Layer Demonstrator Option
H-6910-55 Lift and Drag Force Demonstrator Option
H-6910-70 Pressure Wing and Rake Option
H-6910-71 Wing with Slat and Flap Option
H-6910-80 Probe Accessory Package Option
H-6910-81 Smoke Generator Option
H-6910-CDL (as shown) Computer Data Logging Option (LabVIEW w/o Software)

H-6645 SERIES/PARALLEL PUMP TRAINER          

The Hampden Model H-6645 Series/Parallel Pump Trainer is a tabletop unit for the operation and investigation of series and parallel pump operation. The trainer consists of two centrifugal pumps that are fed by a common water reservoir and a PVC plumbing arrangement, along with five valves that allow various configurations to be implemented.
Options:
H-6648 Control Interface Module Option (LabVIEW w/o Software)

IMAGE NOT AVAILABLE

H-6860 CONDUCTION HEAT TRANSFER DEMONSTRATOR    

​The Hampden Model H-6860 Conduction Heat Transfer Demonstrator is designed to allow students to investigate the fundamental aspects of conduction heat transfer. Heat is conducted through test sections to a heat sink. The temperature profile of the test section is monitored with thermocouples and displayed on a digital panel meter.
Options:
H-6860-CDL Conduction Heat Transfer Demonstrator with Computer Data Logging Option (LabVIEW w/o Software)

H-6730 ENVIRONMENTAL CONTROL UNIT 

The Hampden Model H-6730 Environmental Control Trainer has been designed to teach the fundamental principles of room air conditioning. The unit has sufficient capacity to air condition an entire room with control over the temperature, humidity and air movement. The refrigerant used is HFC-134a.

H-LTCS CORE 7 BASED SYSTEM LAPTOP COMPUTER 

The Hampden Model H-LTCS is a fast, rugged, expandable, system that is built to stand-up to the heavy demands of an educational environment. Plenty of expansion capacity in addition to the highest quality components have made the Hampden H-LTCS a performance leader.

H-6535 HYDROSTATICS BENCH 

The Hampden Model H-6535 Hydrostatics Bench consists of an assortment of apparatus needed for experiments into the properties of fluids and hydrostatics.

IMAGE NOT AVAILABLE

H-6807 FLUIDIZATION AND FLUID BED HEAT TRANSFER DEMONSTRATOR  

The Hampden Model H-6807 Fluidization and Fluid Bed Heat Transfer Demonstrator demonstrates air flow through packed or fluidized bed of granular material as well as heat transfer.
Options:
H-6807-CDL Fluidization and Fluid Bed Heat Transfer Demonstrator with Computer Data Logging Option (LabVIEW w/o Software)

H-6862A THERMO CONDUCTION DEMONSTRATOR     

​The Hampden Model H-6862A Thermo Conduction Demonstrator allows students to investigate in detail the principles of conduction heat transfer. The student is able to determine the relationship governing conduction heat transfer and show that it is dependent on the thermal conductivity of the material, the length of the conducting path, the cross-sectional area of the conduction path, and the temperature gradient. The student is able to determine linear and radial temperature surface contact resistance, conduction through materials with different cross-sectional areas, conduction through insulation, and conduction through composite materials.
Options:
H-6862A-CDL Thermo Conduction Demonstrator with Computer Data Logging Option (LabVIEW w/o Software)

H-6526 GROUND WATER FLOW TANK          

The Hampden Model H-6526 Ground Water Flow Tank provides a means of investigating simple three dimensional flow models utilizing sand as a medium.

H-6850-30 DOUBLE-PIPE HEAT EXCHANGER (AIR TO WATER)   

The Hampden Model H-6850-30 Double-Pipe Heat Exchanger has been developed to permit the experimental determination of the different heat transfer coefficients. Heated air is passed through a tube around which cooling water flows. The air, water and tube temperatures are monitored at the inlet and outlet ports along with the air and water flow rates. In addition, the velocity and temperature profiles within the air tube can also be measured.

H-6642 AXIAL FAN DEMONSTRATOR 

The Hampden Model H-6642 Axial Fan Demonstrator provides hands-on introduction to fan performance. The Trainer utilizes differential pressure transducers for flow rate and pressure across the fan, type T thermocouple to record air temperature and photo tachometer transducers to measure fan speed.

H-6981 CENTRIFUGAL PUMP TEST DEMONSTRATOR     

The Hampden Model H-6981 Centrifugal Pump Test Demonstrator provides a hands-on introduction to the centrifugal pump allowing exploration of pumping mechanics and their effects.

H-6822 REFRIGERATION CYCLE DEMONSTRATOR 

The Hampden Model H-6822 Refrigeration Cycle Demonstrator provides the student with an introduction to the Second Law of Thermodynamics, which states that heat will not pass from a cold region to a hot region without an external agency. The student will be able to observe the evaporator where heat is taken in as the liquid evaporates at low pressure and the condenser where the high pressure vapor condenses and rejects heat. The compressor uses a work input to increase the pressure vapor and the expansion valve controls the flow of liquid from the condenser back to the evaporator.

H-6720 REFRIGERATION UNIT 

The Hampden Model H-6720 Refrigeration Unit has been developed to illustrate the characteristics of a large scale refrigeration system. The student will be able to investigate the theoretical performance of the refrigeration cycle and compare it with the performance of the actual cycle. Additionally, the unit serves as a source of chilled water for use in heat transfer experiments.
Options:
H-6720-CDL Refrigeration Unit with Computer Data Logging Option (LabVIEW w/o Software)

H-6875 STEAM TO WATER HEAT EXCHANGER  

The Hampden Model H-6875 Steam to Water Heat Exchanger has been developed to permit student study of the characteristics of shell and tube type heat exchangers. The student has the opportunity to determine the effects of water flow rates and temperature for the overall heat transfer coefficient.

H-6883 FORCED CONVECTION HEAT TRANSFER TRAINER    

The Hampden Model H-6883 Forced Convection Heat Transfer Trainer permits student investigation of the phenomena of forced convection. This unit allows the student to determine the overall heat transfer coefficient, convective heat transfer coefficient, heat transfer rate, Nusselt Number and Stanton Number.

H-6940 MULTI-PURPOSE FLUME 8 FOOT     

The Hampden Model H-6940 Multi-Purpose Flume has been developed to investigate the basic principles of fluid mechanics. Among the investigations covered are various weirs, flume, gate siphon and spilling.
Options:
H-6940-10 Channel Extension Option (8 ft. (2.5m), H-6940-11 Roughened Bed Option (8 ft. (2.5m), H-6940-12 Raised Channel Bed Option, H-6940-13 Overflow Spillway Option, H-6940-14 Flow Splitter Option, H-6940-15 Syphon Spillway Option, H-6940-16 Radial Gate Option, H-6940-17 Culvert Fitting Set Option, H-6940-18 Pitot Tube with Manometer Option

www.hampden.com/logo

H-6821 WATER CHILLER DEMONSTRATOR   

The Hampden Model H-6821 Water Chiller Demonstrator demonstrates the fundamental aspects of a water chiller system. This system utilizes a double pipe evaporator and condenser and allows the student to measure temperature and pressure at critical points throughout the cycle to better understand the various changes that occur in the cycle.
Options:
H-6821-CDL Computer Data Logging Option (LabVIEW w/o Software)

H-6647 PLUNGER PUMP TRAINER 

The Hampden Model H-6647 Plunger Pump Trainer provides hands-on introduction to a positive displacement pump. This type of pump is used to move small quantities of liquid at a high pressure. The trainer utilizes a plunger pump which is similar to a piston pump except that the sealing gland is at one end of the cylinder. Data is recorded when this unit is interfaced with the Hampden Model H-6648 Control Interface Module.

H-6648 CONTROL INTERFACE MODULE 

The Hampden Model H-6648 Control Interface Module provides the control and computer data logging components for the Hampden Model H-664 Series table-top trainers.

H-6925 FLUID CIRCUIT DEMONSTRATOR W/ H-6927-10 DIGITAL MANOMETER     

The Hampden Model H-6925 Fluid Circuit Demonstrator provides complete facilities for the investigation of the phenomena associated with incompressible fluid flow in conduits.
Options:
H-6925-CDL (as shown) Fluid Circuit Demonstrator with Computer Data Logging Option (LabVIEW w/o Software)
H-6925-10 Pitot Tube Option
H-6925-11 Flow Nozzle Option
H-6925-12 Vortex Flowmeter Option
H-6925-12-CDL Vortex Flowmeter w/Computer Data Logging Option
H-6925-13 Turbine Flowmeter Option
H-6925-13-CDL Turbine Flowmeter w/Computer Data Logging Option
H-6925-14 Magnetic Flowmeter Option
H-6925-14-CDL Magnetic Flowmeter with Computer Data Logging Option
H-6925-15 Differential Pressure Transducer Package Option
H-6925-16 Venturi Profile Valve Kit Option
H-6925-20 Orifice Plate Option (Bore Diameter 0.7343")
H-6925-21 Orifice Plate Option (Bore Diameter 0.5772")
H-6925-22 Orifice Plate Option (Bore Diameter 0.3824")
H-6925-23 Orifice Plate Option (Bore Diameter 0.2846")
H-6925-24 Orifice Plate Option (Bore Diameter 0.2546")
H-6925-30 Globe Valve Option
H-6925-31 Butterfly Valve Option
H-6925-32 Needle Valve Option
H-6925-33 Expansion/Contraction Option
H-6925-40 Extended Bushing Option
H-6925-41 Eccentric Couplings Option
H-6925-42 Reducers Option
H-6925-50 1/2" Plastic & Steel Pipe Set Option
H-6925-99 Centrifugal Pump Option
H-REM-LD-D Load Cell (for above)
H-6925-MR Mobile Storage Cart Option

H-6971 DESKTOP HYDROKINETICS DEMONSTRATOR     

The Hampden Model H-6971 Desktop Hydrokinetics Demonstrator is the benchtop version of our popular Model H-6970 Hydrokinetics Demonstrator. This unit demonstrates the characteristics of turbulent and laminar flow, significance of Reynolds Numbers, flow around objects, velocity distribution in duct flow, formation of shock waves by an air foil, two dimensional flows, the Karman Street Vortex, diffuser performance and the conditions at enlargement and contraction passage.

H-6882 CONVECTION HEAT TRANSFER DEMONSTRATOR    

The Hampden Model H-6882 Convection Heat Transfer Demonstrator permits student investigation of the phenomena of natural (free) and forced convection. Electrically heated test sections are utilized to transfer heat to both still and moving air. The unit allows the student to determine the overall heat transfer coefficient, convective heat transfer coefficient, heat transfer rate, Nusselt Number and Stanton Number.
Options:
H-6882-CDL Convection Heat Transfer Demonstrator with Computer Data Logging Option (LabVIEW w/o Software)

H-6850-10 DOUBLE-PIPE HEAT EXCHANGER (OIL TO WATER)  

The Hampden Model H-6850-10 Double-Pipe Heat Exchanger has been developed to enable students to investigate in detail the heat-transfer characteristics of a double-pipe heat exchanger. The working fluids of this unit are water and oil.

H-6850-21 CONCENTRIC TUBE HEAT EXCHANGER   

The Hampden Model H-6850-21 Concentric Tube Heat Exchanger has been developed to investigate the fundamental principles of heat transfer as applied to a tube-in-tube heat exchanger. The apparatus permits the student to move from classroom theory to a hands-on application with all of the practical training. The student shall measure the variables that affect the overall heat transfer coefficient. The "cold" and "hot" fluid temperatures and flow rates are monitored at strategic locations. The unit can be configured to operate as either a parallel flow or counterflow heat exchanger. By varying the fluid flow rates, laminar, transitional or turbulent flow conditions can be created.
Options:
H-6850-21-CDL Concentric Tube Heat Exchanger with Computer Data Logging Option (LabVIEW w/o Software)

H-6850-40 SHELL & TUBE HEAT EXCHANGER   

The Hampden Model H-6850-40 Shell and Tube Heat Exchanger is designed to provide students with a comprehensive study of shell and tube heat exchanger characteristics. Students will be able to determine the effects of water flow rates and inlet water temperatures on the overall heat transfer coefficient.
Options:
H-6850-40-CDL Shell & Tube Heat Exchanger with Computer Data Logging Option (LabVIEW w/o Software)

H-6510 DRAINAGE AND SEEPAGE TANK DEMONSTRATOR          

The Hampden Model H-6510 Drainage and Seepage Tank Demonstrator has been developed to investigate water flow through permeable media. Using sand as the medium and two-dimensional models, flow lines can be determined as well as the distribution of up-lift pressure and seepage rates.

H-6830 EDUCATIONAL MECHANICAL HEAT PUMP 

The Hampden Model H-6830 Educational Mechanical Heat Pump demonstrates the principle that heat will move from a high temperature to a lower temperature as first proposed by Lord Kelvin over 100 years ago. The Hampden Model H-6830 Educational Mechanical Heat Pump is known as a water to air system.
Options:
H-6830-CDL (as shown) Educational Mechanical Heat Pump with Computer Data Logging Option (LabVIEW w/o Software)

H-6879 NUCLEATE BOILING HEAT TRANSFER DEMONSTRATOR    

The Hampden Model H-6879 Nucleate Boiling Heat Transfer Demonstrator is designed to show heat transfer by convection boiling, nucleate boiling and film boiling from a heating element in a pool at saturated conditions.
Options:
H-6879-CDL (as shown) Nucleate Boiling Heat Transfer Demonstrator with Computer Data Logging Option (LabVIEW w/o Software)

H-6878 6-PASS HEAT EXCHANGER DEMONSTRATOR   

The Hampden Model H-6878 6-Pass Heat Exchanger Demonstrator allows the student to investigate in detail the heat transfer characteristics of several different types of heat exchangers under various flow conditions.
Options:
H-6878-CDL 6-Pass Heat Exchanger with Computer Data Logging Option (LabVIEW w/o Software)
H-6878-10 Mobile Electric Steam Boiler

H-6530 HYDRAULIC DEMONSTRATION CHANNEL  

The Hampden Model H-6530 Hydraulic Demonstration Channel is designed to investigate analytical applications of fluid mechanics to situations in which fluids can be treated as continuous media. The particular laws involved include conservation of mass, continuity, energy, and momentum. Application of these laws may be simplified in order to describe quantitatively the behavior of the fluid. H-6530-10-6 Pipe Flow Set is included with Model H-6530.
Options:
H-6530-11-6 SAF Stilling Basin Option
H-6530-12-6 Pipe Drop Inlet Option
H-6530-13-6 Hydraulic Jump Basin Option
H-6530-14-6 Sluice Gate with Pressure Taps Option
H-6530-15-6 Weir - V-Notch Option
H-6530-16-6 Weir - Broad Crest Option
H-6530-17-6 Spillway Section Option
H-6530-18-6 Inclined Slope Option
H-6530-19-6 Contraction/Expansion Section Option (Requires H-6530-10-6)
H-6530-20-6 Wave Generator Option
H-6530-21 Venturi Meter Option (Requires H-6530-10-6)
H-6530-22 Flow Nozzle Pipe Section Option (Requires H-6530-10-6)
H-6530-23-6 Gauge Carrier Option
H-6530-24 Pitot Tube Option (Requires H-6530-23-6)
H-6927-10 Digital Differential Pressure Manometer Option
H-6530-26 Reynold's Experiment Apparatus Option (Requires H-6530-23-6)
H-6530-27 Hook & Point Gauges for precise measurement of water surface elevation Option (Requires H-6530-23-6)
H-6530-31-6 Crump Weir Option

Computer Data Logging Data
Computer Data Logging and Control

H-6840 EDUCATIONAL THERMO-ELECTRIC PUMP 

The Hampden Model H-6840 Educational Thermo-Electric Pump demonstrates the Peltier Effect. In 1834, Jean C. A. Peltier discovered that the passage of an electrical current through the junction of two dissimilar conductors cools or heats the junction, depending on the direction of current. It turns out that the heat generation (or absorption rate) is proportional to the magnitude of the current and dependent on the temperature of the junction. The Thermo-Electric effect has applications in the field of mini-temperature control requirements for electronics, space and missile internal guidance systems.
Options:
H-6840-CDL Educational Thermo-Electric Pump with Computer Data Logging Option (LabVIEW w/o Software)

H-6320 STRUCTURES TEST SYSTEM BASE 

The Structures Test System is a bench-top sized "learning laboratory" system designed to test and indicate the effects of static and dynamic mechanical loading on models of various engineering components and structures such as beams ("I"-beams, "T"-beams, rectangular and round beams, etc.), simple and complex bridge trusses, cantilever beams and trusses, crane trusses and the like.
Options:
H-6320-10 Plastic Beam Option
H-6320-20 Wing-beam with Whiffle Tree Option
H-6320-30 Determinate Bridge Truss Option
H-6320-30RK Replacement Kit for H-6320-30
H-6320-40 Indeterminate Bridge Truss Option
H-6320-40RK Replacement Kit for H-6320-40
H-6320-50 Horizontal Beam Option
H-6320-60 Crane Beam Option
H-6320-70 Vertical Extension Channel Option
H-6320-71 Flat Beam Assembly Option
H-6320-72 Three Part Beam Assembly
H-6320-73 Suspension Bridge
H-6320-74 U and S Shape Frames
H-6320-CDL (as shown) Structures Test System Base with Computer Data Logging Option

H-6870 COOLING TOWER DEMONSTRATOR W/COLUMN 3: 110SQ.M PER CU.M. 

The Hampden Model H-6870 Cooling Tower Demonstrator was developed to investigate the principles of evaporative cooling used in industrial applications. Model H-6870 Cooling Tower Demonstrator shown with Model H-6870-30 Water Distribution Column 3 (included)
Options:
H-6870-10 Water Distribution Column 1: Empty
H-6870-20 Water Distribution Column 2: Packing Density 77sq.m. per cu.m.
H-6870-30 Water Distribution Column 3: Packing Density 110sq.m. per cu.m. (included with H-6870)
H-6870-40 Water Distribution Column 4: Packing Density 200sq.m. per cu.m.
H-6870-50 Water Distribution Columns 5: Packing Characteristics Column
H-6870-CDL Cooling Tower Demonstrator with Computer Data Logging Option (LabVIEW w/o Software)

H-6311 TORSION TEST DEMONSTRATOR          

The Hampden Model H-6311 Torsion Test Demonstrator allows the student to examine the torque-transmitting behavior of various materials such as aluminum, steel and copper. The relationship between torque and angle of twist can be examined. The behavior of specimens made of the same materials, but of different geometric cross sections, can be compared. Maximum torsional shearing stress of specimens can be calculated using strain gauges.

H-CS CORE 3 BASED SYSTEM 

The Hampden Model H-CS is a fast, rugged, expandable, American-made system that is built to stand-up to the heavy demands of an educational environment. Plenty of expansion capacity in addition to the highest quality components have made the Hampden H-CS a performance leader.

H-6990 TILTING WATER CHANNEL AND GATE         

The Hampden Model H-6990 Tilting Water Channel and Gate System is designed for use as a general purpose center pivot flume. With it, one can demonstrate and investigate steady and unsteady flow, sediment transportation, weirs, sluice gates and wave phenomena. The channel consists of a head tank, working section and a tail tank.

H-6535-7 VISCOSITY DEMONSTRATOR          

The Hampden Model H-6535-7 Viscosity Demonstrator provides the student with the means to perform experiments in the measure of viscosity. The application of shear stress to a fluid results in the continual and permanent distortion known as flow. Viscosity is the resistance of a fluid to its internal friction i.e. Shear motion. This resistance is due to cohesion of the molecules and molecular transfer from one layer to another setting up a tangential or shear stress. Cohesion predominates in liquids, as temperatures increase cohesion decreases as does viscosity.