The Hampden Model H-RST-20 Geothermal Trainer provides hands-on training by allowing students to conduct tests and adjustments on a modern Geothermal Heat Pump System. The H-RST-20 Geothermal Trainer is equipped with: 1. Exclusive double isolation compressor mounting system 2. Insulated divider and seperate compressor/ air handler compartments 3. Extended range operation 4. Exceeds ASHRAE 90.1 efficiencies 5. Internally trapped condensate drain line 6. Unit Performance Sentinel performance monitoring system.
H-RST-20-FP-6E Electrical Fault Package Option
H-RST-20-DMP Digital Meter Package Option
The Hampden Model H-SHST-1 Solar Heat Service Trainer contains the actual control components of a solar heating system, including: sensors, relays and thermostats. Each component terminates at Hampden binding posts for easy interconnection into several configurations. Up to 21 faults may be inserted from the panel on the rear.
The Hampden Model H-6526 Ground Water Flow Tank provides a means of investigating simple three dimensional flow models utilizing sand as a medium. A multitube manometer is used to show profile and make level measurements at appropriate locations.Tank demonstrations provide the student with practical experiments about land drainage, flood risk, wells, and drainage of lakes or ponds.
The Hampden Model H-PVIT-MAST Mobile Solar Array with Solar Tracking System
is an optical sensing system used to sense and track the suns position throughout the day. The sensors feed information to the control box where it processes information on direct component of sunlight available, the diffuse amount of sunlight, the total amount of sunlight as well as the differential amount of sunlight on opposing sensors. The Hampden Models H-PVIT-MAST Mobile Solar Array w/ Solar Tracking Option and H-PVIT-MA Mobile Solar Array Option are options of Hampden Model H-PVIT-1 Photovoltaic Installers Trainer and are dependant upon it.
P.O. Box 563
East Longmeadow, MA 01028
(Toll Free) 800-253-2133 or 888-HEC-CORP
TheHampden Model H-SPT-AC-1-HS Table Top Solar Photovoltaic Trainer is a control system trainer which lets the student technician examine the electrical layout and operational features normally associated with a photovoltaic power source. The trainer demonstrates the electrical characteristics of the solar array, storage battery, AC and DC distribution, and AC and DC loading. The complete charging sequence can be observed.
The Hampden Model H-FCTT-1 Fuel Cell Technology Trainer allows the student to create a grid independent power supply that uses only hydrogen as its fuel. The system familiarizes the student with fuel cell power supply technology, an environmentally friendly method of generating power directly from a hydrogen reaction. Fuel cells are the most promising alternate energy supply and are already being used in a number of areas, including automotive engineering and power generation systems. The Model H-FCTT-1 can also be connected to an external energy source, such as a solar panel or wind generator, for comparison between the different technologies. A switch located on the panel allows for switching between the fuel cell and an external source.
The Hampden Model H-SST-3 Solar Heat System Trainer is an actual solar hot water heating system. System components include 2 vacuum tube solar collector sections. The trainer is mounted on a mobile frame and the collector panel is adjustable for easy positioning in direct sunlight.
The Hampden Model H-6520 Infiltration Demonstrator investigates the infiltration rates of different soil types and soil surface treatments. (shown with accessories)
The Hampden Model H-PVIT-1 Photovoltaic Installers Trainer has been designed with the latest Industrial/Commercial components available. The trainer will provide the necessary training in completing a fully functioning, grid-tied solar electric system. This system will have the capability to be fully monitored and controlled.
The Hampden Model H-HYD-1A Solar Hydronics Trainer contains the plumbing components typically found on most active solar-heated circulating hot water heating systems. It includes both the storage (open) loop and the exchange (closed) loop. The solar collector is represented in the exchange loop by two parallel piping segments that include clear plexiglas tubing. The trainer is completely self-contained, tested, and ready for operation, except for the addition of water to the storage and exchange loops.
Copyright 2019 CLICK WebDesigns
The Hampden Model H-6529 Flocculation Test Unit is used to determine optimal chemical dosages for flocculation. The Flocculation Test Unit helps you to determine the exact amount of alum or polymer necessary to trigger flocculation.
The Hampden Model H-ACTK-23 includes compressor, cap and clamp kit, electric pressure control (2), contactor, transformer, filter drier, sight glass, evaporator and condenser. Dimensions: 24-1/8"D x 38"W x 60"H
The Hampden Model H-6528 Filterability Index Unit has been developed to investigate filters and how they relate to water treatment. The student will be able to evaluate the operation and principles of filter operation, filtration procedures and the measurement of filterability of suspended sedimentation.
The Hampden Model H-6516 Ion Exchange Demonstrator is a bench mounted unit designed to demonstrate the use of ion exchange resins for either continuous water softening or demineralization. The equipment is designed to emulate the industrial operation of such units, including monitoring breakthrough and regeneration cycles.
The Hampden Model H-6510 Drainage and Seepage Tank Demonstrator has been developed to investigate water flow through permeable media. Using sand as the medium and two-dimensional models, flow lines can be determined as well as the distribution of up-lift pressure and seepage rates.
The Hampden Model H-6524 Mobile Bed and Flow Visualization Tank Demonstrator is used to investigate flow visualization and mobile bed situations in relation to Civil Engineering structures. This unit incorporates a sediment well with removable Lexan® cover for mobile bed investigations. Shown is the MODEL H-6524-CDL.
IMAGE NOT AVAILABLE
The Hampden Model H-SPT-AC-1A Solar Photovoltaic Trainer contains two solar photovoltaic modules with a nominal voltage output of 15.5V DC at 2.26A, an inverter that converts the DC to single-phase AC, a high-capacity solar battery, controls to monitor power from solar modules and to switch to battery power when necessary, four test points, two power take-off points (12V DC and 120V AC), a 0-15V DC voltmeter, a multi-range DC ammeter, and a 0-150V AC voltmeter. The mobile frame is constructed of code gauge furniture stock steel with four swivel casters, two with locks. Furnished complete with a set of interconnecting cords.
The Hampden Model H-SST-1A Solar System Trainer is an actual solar hot water heating system. System components include a solar collector, circulation pumps, storage tank, heat exchanger, air separator, air handler, solar heating coil, automatic air vents, thermostat, and a control panel with sensors. Gauges, thermometers, and flowmeters permit students to observe pressures, temperatures, and flow rate while the system is in operation. The trainer is mounted on a mobile frame and the collector panel is adjustable for easy positioning in direct sunlight.
H-SST-1A-FP Electrical Fault Package Option
The Hampden Model H-SST-4 Solar Heat System Trainer is an actual solar hot water heating system. System components include one (1) traditional style solar collector and one (1) vacuum tube solar collector, circulation pumps, storage tank, heat exchanger, air separator, air handler, solar heating coil, automatic air vents, thermostat, and a control panel with sensors.
The Hampden Model H-6517 Aeration Unit has been developed to investigate oxygen transfer characteristics of diffused air systems along with physical and chemical parameters which effect oxygenation in terms of retention time. The level of Dissolved Oxygen (DO) in water depends on many physical, chemical and biochemical activities in the sample. The most important factors to consider are pressure, temperature and salinity. The amount of oxygen a sample can hold in a solution will vary with the temperature of the sample, the pressure or altitude at which the sample is measured and the concentration of salts dissolved in the sample. The analysis of DO is one of the key tests performed in water pollution and waste water treatment studies.
The Hampden Model H-SHSP-1 Solar Heat and Solar Photovoltaic Trainer is a fully mobile solar heat solar photovoltaic control system trainer which lets the student technician examine the hot water and electrical layouts and operational features normally associated with a solar heating system and photovoltaic power source.
The Hampden Model H-WPG-1B Wind Powered Generator has been designed to provide the student with the basic understanding of how wind generators function as an alternate source of energy. This system consists of a wind source, a four bladed DC wind generator, control panel and base assembly.
H-WPG-FP Electrical Fault option
H-WPG-P Pump option
H-WPG-CDL Computer Data Logging option - Consisting of a hand held anemometer with realtime data logging capability.
The Hampden Model H-6519 Permeability/Fluidization Studies Trainer is designed to investigate the measurement and characteristics of flow through a bed of particles. The trainer consists of metal framework, transparent test section module, constant head module, valve and flowmeter module, water manometer, digital manometer, interconnection tubing and glass beads for the test column.
The Hampden Model H-6527 Sedimentation Study Trainer has been developed to investigate the physical processes of sedimentation. The student will be able to evaluate and measure the particles as to height, size and settling rates for making up the sedimentation curve.
The Hampden Model H-HEAT-1A Home Efficiency Auditor TESTING Facility will allow potential auditors to learn the proper techniques in performing a complete energy audit. Some of the areas covered are consistent data collection, insulation inspection, HVAC analysis, base load consumption, air leakage, energy usage, along with many more vital areas. Along with helping develop these skills the Hampden Model H-HEAT-1A is provided with an intricate fault package. This fault package will create a realistic situation that will require the auditor to diagnose the problem and specify maintenance or repair.
H-HEAT-TEP Test Equipment Package
H-HEAT-CC Curriculum and Certification Package
H-HEAT-MTP Mobile Trailer Package
The Hampden Model H-6523A Sediment Transport Demonstrator investigates suspended sediment in a moving stream and bed load movement. The moving stream can be controlled over a wide range to simulate fast flowing streams or slow moving rivers, demonstrating the various size and density of partial deposits. Slope is adjustable from 0-10%.
The Hampden Model H-6521 Model Sedimentation Tank has been developed to investigate the hydraulic characteristics and setting efficiencies of a model settling basin. The student will be able to evaluate how non-uniform flows occur and its interaction with sediment settling characteristics.
The Hampden Model H-6518 Aerobic Digester is a bench top trainer designed as a comprehensive study facility of biological water treatment processes. A synthetically prepared waste water is used to gain a working knowledge of the operational parameters and purification efficiencies.
The Hampden Model H-6515 Anaerobic Digester is a bench top trainer designed to demonstrate the fundamentals of the anaerobic treatment processes. Anaerobic treatment processes involve bacteria which function only in the absence of air. These processes are becoming more popular in the water treatment industry, as they have considerable advantages over aerobic processes, including low sludge production, tolerance of stop/start operation, production of a useful fuel (methane), and relatively high throughput.
The Hampden Model H-GTL-2 Geothermal Trainer provides hands-on training by allowing students to conduct tests and adjustments on a modern Geothermal Heat Pump.
The Hampden Model H-6809 Solid Handling Investigation Bench has been designed to allow students to familiarize themselves with various methods of handling solids through blending, separating, sizing, discharge rates, angle of repose, grinding, and material transport.
The Hampden Model H-GTL-1 Geothermal Trainer provides hands-on training by allowing students to conduct tests and adjustments on a modern Geothermal Heat Pump.