H-RST-17 HEAT PUMP TRAINER (R134A)  

The Hampden Model H-RST-17 Heat Pump Trainer will allow the student to study the thermodynamic cycle of the typical heat pump. This system supplies either heating or cooling for a separate closed circuit air handler.
Options:
H-RST-17-CDL Heat Pump Trainer with Computer Data Logging & Software Option (R-134a)
H-RST-DMB Digital Manifold with Bluetooth Option

IMAGE NOT AVAILABLE

Copyright 2021  CLICK WebDesigns

H-AHST-D AIR & HYDRONICS GAS/OIL HEATING TRAINER WITHOUT A/C   

The Hampden Model H-AHST-D combination forced air and hydronic (circulating hot water) heating trainer shall provide demonstration and experimentation in combustion, control systems, heat transfer, without A/C.

H-AHST-D4 AIR & HYDRONICS GAS/GAS HEATING TRAINER WITH A/C 

The Hampden H-AHST-D4 combination forced air and hydronic (circulating hot water) heating trainer shall provide demonstration and experimentation in combustion, control systems, heat transfer, summer cooling.

H-RST-21A MINI-SPLIT TYPE HEAT PUMP TRAINER    

The Hampden Model H-RST-21A Mini Split-Type Heat Pump Trainer provides a hands-on introduction to the principle components of heating and air conditioning. This system places the indoor unit (evaporator) remotely from the outdoor unit (condenser) providing a quiet, no air flow restriction, and secure system. 

H-ACCS-1A AIR CONDITIONING CONTROL SYSTEM  

The Hampden Model H-ACCS-1A Air Conditioning Control System contains the actual components used in the control of commercial and residential heating/cooling systems. All components are prewired into a complete thermostat-actuated control system and then diagrammed to facilitate understanding and use.

H-PCT-1 PNEUMATIC CONTROLS TRAINER  

The Hampden Model H-PCT-1 Pneumatic Controls Trainer is designed to aid students in learning the operation and maintenance of commercial pneumatically-controlled heating/cooling systems.

HAMPDEN ENGINEERING CORPORATION


​sales@hampden.com

P.O. Box 563

​East Longmeadow, MA 01028

​(Toll Free) 800-253-2133 or 888-HEC-CORP

Local: 413-525-3981

​Fax: 413-525-4741​

H-FAHT-1E ELECTRIC-FIRED FORCED AIR HEATING TRAINER   

The Hampden Model H-FAHT-1E Gas-Fired Forced Air Heating Trainer shall provide demonstration and experimentation in combustion, control systems, and heat transfer.

H-RST-12 HEAT PUMP TRAINER (R-134A)    

The Hampden Model H-RST-12 Heat Pump Trainer provides the student with an introduction to the principle components of heat pump systems. For practical electrical troubleshooting, the instructor has the ability to insert eighteen commonly found electrical faults such as: defective capacitor, motor, and timer. The instructor may also insert two mechanical faults such as a defective thermal expansion valve and defective filter-drier.
Options:
H-RST-12-CDL Heat Pump Trainer with Computer Data Logging & Software Option (R-134a)
H-RST-DMB Digital Manifold with Bluetooth Option

H-FAHT-1-G-1A FORCED AIR HEATING TRAINER WITH SUMMER AIR   

The Hampden Model H-FAHT-1-G-1A Gas-Fired Forced Air Heating Trainer with Air Conditioning shall provide demonstration and experimentation in combustion, control systems, and heat transfer. (H-FAHT-1-G-1A-CDL shown)

H-AHST-D2 AIR & HYDRONICS GAS/OIL HEATING TRAINER WITH A/C   

The Hampden Model H-AHST-D2 combination forced air and hydronic (circulating hot water) heating trainer shall provide demonstration and experimentation in combustion, control systems, heat transfer, and A/C.

H-AHST-D3 AIR & HYDRONICS GAS/ELECTRIC HEATING TRAINER WITH A/C 

The Hampden Model H-AHST-D3 combination forced air and hydronic (circulating hot water) heating trainer shall provide demonstration and experimentation in combustion, control systems, heat transfer, summer cooling.

H-VRST-1 VARIABLE REFRIGERANT SYSTEM TRAINER    

The Hampden Model H-VRST-1 Variable Refrigerant System Trainer combines a Daikin VRV heat pump with three indoor units (1 - ceiling mounted cassette, 1 - wall mounted unit and 1- floor standing unit.) each with its own digital controller. The system is built on a 10’L x 2.5’W x 7’H platform and includes all the components carefully arranged to provide maximum accessibility to the student. All equipment and hardware is of commercial quality and is typical of that encountered in the field by the service technician. A computer is built into the trainer and is loaded with Daikin’s Data Acquisition Software.

hvac

Heating/Cooling

HEE-11 HEATING AND A/C ELECTRICAL WIRING TRAINER  

The Hampden Model HEE-11 Heating & Air Conditioning Electrical Wiring Trainer is designed to cover low voltage pilot circuits as well as series and parallel circuits.

H-RST-8 HEAT PUMP TRAINER (R-134A)  

The Hampden Model H-RST-8 Heat Pump Trainer provides students with an introduction to the principal components of heat pump systems. The instructor is able to insert eighteen electrical faults, including: defective fan motor, switches, relay and compressor faults.
Options:
H-RST-8-CDL Heat Pump Trainer with Computer Data Logging & Software Option (R-134a)
H-RST-DMB Digital Manifold with Bluetooth Option

H-HEAT-2A AIR DISTRIBUTION SYSTEM TRAINER   

The Hampden Model H-HEAT-2A Air Distribution System Trainer is designed to acquaint the student with the fundamentals of air movement found in a typical residential dwelling. The trainer aids the student in acquiring a better understanding of static pressures, back drafting, air leakage and thermal boundaries. The trainer shows the student how air moves under various conditions created in a residential dwelling.
Options:
H-HEAT-2A-MT Mobile Table

H-OBF-2B OIL BURNER FURNACE CONTROL DEMONSTRATOR   

The Hampden Model H-OBF-2B Oil Burner Furnace Control Demonstrator provides students with experience in connecting and operating two standard residential oil-fired furnace control systems for both winter heating and summer cooling. It contains all the standard control components used with isolated heating/cooling systems of oil-fired furnaces with the cadmium sulfide flame sensing relay. Pilot lamps indicate the operation of the simulated air conditioning contactor, the oil burner, and the blower motor. Model H-OBF-2B is shown.​​
Options:
Model HMC-3 Mobile Cart

H-ACCS-2A A/C-HEAT PUMP TRAINER  

The Hampden Model H-ACCS-2A Air Conditioner/Heat Pump Controls Trainer provides students with the opportunity to operate, test, and troubleshoot the electrical controls of a motel-type air conditioning unit that includes a heat pump. It contains the actual control components and devices.

www.hampden.com/logo

H-FAHT-2 FORCED AIR HEATING TRAINER  

The Hampden Model H-FAHT-2 Gas-Fired Forced Air Heating Trainer shall provide demonstration and experimentation in combustion, control systems, and heat transfer.

H-SZCT-2A SINGLE ZONE CONTROL TRAINER  

The Hampden Model H-SZCT-2A contains all of the control components of a roof top, two-stage, heating/cooling commercial air conditioning system including outside air damper control, heating setup and cooling setup, temperature and C02 sensor, transformers, a programmable thermostat, and control relays.

HEE-11A-FT-1C INTERMEDIATE ELECTRICITY TRAINER  

The Hampden Model HEE-11A-FT-1C Intermediate Electricity Trainer provides students with the opportunity of wiring actual heating and cooling control components into realistic electrical circuits. Further, the instructor may insert up to 15 faults to provide students with troubleshooting experience.

H-GC-2A GAS CONTROLS TRAINER   

The Hampden Model H-GC-2A Gas Controls Trainer provides students with experience in connecting and operating three standard residential gas-fired furnace control systems for both winter heating and summer cooling. It contains all the standard control components for the following three types of systems: (1) single-function gas valve and pilotstat switch, (2) combination gas control valve system, (3) powerpile system. Pilot lamps indicate the operation of a simulated furnace blower and air conditioning compressor.
Options:
Model HMC-3 Mobile Cart

H-FAHT-1-G GAS FIRED FORCED AIR FURNACE   

The Hampden Model H-FAHT-1-G Gas-Fired Forced Air Heating Trainer shall provide demonstration and experimentation in combustion, control systems, and heat transfer. 
(H-FAHT-1-G-A-CDL shown)

H-AP-2 AIR DISTRIBUTION SYSTEM TRAINER  

The Hampden Model H-AP-2 Air Distribution System Trainer is designed to acquaint the student with the fundamentals of air movement found in typical forced air heating and air conditioning systems. The trainer aids the student in acquiring a better understanding of static pressures, velocity pressures, and air volumes. The trainer shows the student how air moves under various conditions created in the distribution system.

NO DATA FILE​